Lots of sanding and assembly this week.
A few more address changes.
I'll post some pics towards the end of the week of pre-shipment parts.
Surveys Unlocked - Need to update your shipping address?
Your surveys are open and ready to update your addresses.
We'll leave them open until we ship your rewards, but get on it and get them updated ASAP.
Thanks everyone!... Read more
End of May
Fusions are shipping on an erratic basis.
Along with our other projects we're sending these out the door.
Nothing new to report.
Any change of address needed?
Send us mail... Read more
Its way past time.
Today the digital, tomorrow the physical I went to write a new program for the Half-Cores and some other parts, and I did my pre-writing... Read more
First Flume Fusions ship this week.
We're finising off paperwork and setting up fulfillment shiipping now and wil have the first fusions out the door in a few day.
For after the show.
These need magnets and finish work but just wanted to drop in and show you what we've been up two while making parts for ECCC this... Read more
Working on all projects.
Nothing new to report.
We're still here working hard for you.
New year with new goals and rewards for us all. So, here's what's up.
1. OrcaCon is happening January 12-14 here in Seattle (Bellevue actually) We're going and we're... Read more
180 degrees about face...
While we were working on these we did a quick review of all our projects and found that we were way behind on our GM Screens. These screens came before... Read more
Welcome to the windy season everyone, at least that's what November means to us here at ZucatiCorp.
Rain, Winds and early darkness. Fall.
Production is under way and the big... Read more
We've got the liner pattern ready to go, so for anyone who wants the digital proof,
Send us some mail and we'll send it along.
The Flume Fusion is in the work cue.
Planning is done and most materials are purchased.
They're in line to begin production some time in November.
In the mean time here's what we were working on in the... Read more
All is well...
Same schedule and same plans.
These and the quarter and half cores will go into production soon.
Nothing, just some seriously rare wood I thought it'd... Read more
Final Version complete.
So, there it is... new base, new tower... new new new.
The template for the liner insert is very similar but we'll be releasing a... Read more
Saying hello here at the end of September.
No changes and no starting till at least the beginning of November at this point.
Will update everyone when I nail down... Read more
Quick end of August update
Nothing has changed.
All is proceeding nicely.
Contact direct if you have questions or needs.
I'm working through the last bunch of e-mails this week so if you've written already... Read more
Production V1 is ready to make....
Based on feedback and testing I've done some re-tooling on the FLUME FUSION to allow for zero interference of the dice with the flume when closed...
See this cool review... Read more
The After Party...
Quick view into some of the choices backers are making to customize their FLUME FUSIONS.
Still a bit over 100 backers to go so these numbers can... Read more
Lining pictures added.
I've added a selection of linings from cork to several colors of felt.
Thanks for your patience.
Did these by hand but the production pieces will use punches for clean... Read more
What happens next?
That's right BackerKit Surveys are in the wild and ready for you to go and answer.
Pickup all the FLUME's you ordered, the Dice you added on... Read more
Just 24 hours left!
Or 23 hours now!
This little 5-day campaign has been a HUGE success!
THANK YOU ALL SO MUCH!
Here's what we've got planned.
1. We're going to put together... Read more
Want free Global Shipping?
Pledge at the $25 level or above on both campaigns and receive FREE GLOBAL SHIPPING on both!
Just that easy. - Hal
SPECTRUM is here.
FLUME FUSION... Read more