Transmit or receive any radio signal from 30 MHz to 6000 MHz on USB power with HackRF.
Watch the video above for an introduction to HackRF. Click "Updates" above the video for the latest project information.
HackRF is an open source hardware project to build a Software Defined Radio (SDR) peripheral.
SDR is the application of Digital Signal Processing to radio waveforms. It is similar to the software-based digital audio techniques that became popular a couple of decades ago. Just as a sound card in a computer digitizes audio waveforms, a software radio peripheral digitizes radio waveforms. It's like a very fast sound card with the speaker and microphone replaced by an antenna. A single software radio platform can be used to implement virtually any wireless technology (Bluetooth, ZigBee, cellular technologies, FM radio, etc.).
Digital audio capabilities in general purpose computers enabled a revolution in the sound and music industries with advances such as hard disk recording and MP3 file sharing. Today's computers are fast enough to process radio waveforms in similar ways, and the radio communications industry is going through the same sorts of changes. One critical advance is finally taking place now, and that is the availability of low cost tools enabling anyone to take part in the revolution.
Wide Operating Frequency Range
HackRF operates from 30 MHz to 6 GHz, a wider range than any SDR peripheral available today. This range includes the frequencies used by most of the digital radio systems on Earth. It can operate at even lower frequencies in the MF and HF bands when paired with the Ham It Up RF upconverter.
HackRF can be used to transmit or receive radio signals. It operates in half-duplex mode: it can transmit or receive but can't do both at the same time. However, full-duplex operation is possible if you use two HackRF devices.
You don't have to carry an external power supply with you when taking HackRF on the road because it is powered by USB. It is small enough to fit easily into a typical laptop bag. Your HackRF will be slightly smaller than the beta unit pictured above and will protected by a full enclosure.
HackRF is designed primarily for use with a USB-attached host computer, but it can also be used for stand-alone applications with Jared's HackRF PortaPack, an add-on that gives HackRF an LCD screen, directional buttons, and audio ports.
HackRF was designed to be the most widely useful SDR peripheral that can be manufactured at a low cost. The estimated future retail price of HackRF is $300, but you can get one for even less by backing the Kickstarter project today.
The maximum bandwidth of HackRF is 20 MHz, about 10 times the bandwidth of TV tuner dongles popular for SDR. That means that HackRF could be used for high speed digital radio applications such as LTE or 802.11g.
The most important goal of the HackRF project is to produce an open source design for a widely useful SDR peripheral. All hardware designs and software source code are available under an open source license. The hardware designs are produced in KiCad, an open source electronic design automation tool. You can download the Jawbreaker (HackRF beta) design and build your own HackRF today!
HackRF beta units are already being used on Linux, OS X, and Windows platforms. The device takes full advantage of USB 2.0, an interface found on almost every general purpose computer. HackRF already works with the popular GNU Radio software framework, and HackRF support can be added to other SDR software.
The Jawbreaker design depicted above is the fully functional HackRF beta design. Hundreds of Jawbreakers have been distributed to developers and beta testers. HackRF has already been used for Digital Audio Broadcasting (DAB), Bluetooth monitoring, spectrum sensing, wireless microphones, AIS, FM radio, and more. I plan to use feedback from beta testers to make your HackRF even better than Jawbreaker.
HackRF is designed by Michael Ossmann of Great Scott Gadgets and Jared Boone of ShareBrained Technology. We have had help from many volunteers including Benjamin Vernoux, Dimitri Stolnikov, and others who populate our irc channel (#hackrf on Freenode)
The primary web page for HackRF is:
You can learn about the history of the project and how it was made possible on mossmann's blog:
You can download hardware designs and software source code at:
Project documentation may be found on our wiki:
The open source Ham it Up RF upconverter is designed by Opendous Inc.:
It is manufactured by NooElec:
The HackRF PortaPack is designed by Jared Boone:
Thanks to Hak5 for use of clips from episode 1120:
The HackRF Jawbreaker photograph was taken by fd0:
Risks and challenges Learn about accountability on Kickstarter
Because the beta design has already been tested by many people, it is very unlikely at this point that any technical design challenges will prevent the HackRF project from being a success.
I routinely use a contract manufacturer to produce electronic devices I distribute to resellers, but projects can be delayed for a variety of reasons. The most significant delay I have ever experienced was the HackRF Jawbreaker beta production. I had hoped that the production would be completed in two to three months, but it took a total of seven months. The largest source of delay during Jawbreaker production was component availability. Your HackRF will be scheduled for production further in advance and will benefit from lessons learned during the Jawbreaker production.
I hope that it gives you confidence to know that I already have delivered 500 HackRF beta units and that I successfully delivered Ubertooth One on time to the backers of my first Kickstarter project. It was thanks to the success of Ubertooth One on Kickstarter that I was able to found Great Scott Gadgets, a company that now helps support several open source developers.
Yes, it supports RX and TX.
Transmit performance is expected to be similar to Jawbreaker. See: https://github.com/mossmann/hackrf/wiki/Jawbreaker#transmit-power
The Ham It Up upconverter enables operation in the MF and HF bands (from about 300 kHz to 30 MHz). With HackRF plus Ham It Up, you can transmit or receive signals from 300 kHz to 6 GHz.
It is safe to say at this point that HackRF will be available for sale after the shipments of Kickstarter rewards. I don't yet know the final price ($300 estimated) or exactly how long (probably less than one month after the rewards) you'll have to wait.
seconds to go
Pledge $25 or moreYou selected
PCB: A HackRF printed circuit board you can use to build your own HackRF peripheral or keep as a souvenir.Estimated delivery:Add $5 USD to ship outside the US
Pledge $199 or moreYou selected
100 backers All gone!
EARLY-BIRD: A HackRF peripheral with enclosure and telescopic antenna. Thanks for spreading the word about HackRF!Estimated delivery:Add $15 USD to ship outside the US
Pledge $275 or moreYou selected
HACKRF: A HackRF peripheral with enclosure and telescopic antenna.Estimated delivery:Add $15 USD to ship outside the US
Pledge $310 or moreYou selected
HACKRF-HF: A HackRF peripheral with enclosure and telescopic antenna plus a Ham It Up RF upconverter for MF and HF bands.Estimated delivery:Add $15 USD to ship outside the US
Pledge $550 or moreYou selected
FULL-DUPLEX: Two HackRF peripherals with enclosures and telescopic antennas.Estimated delivery:Add $15 USD to ship outside the US
Pledge $620 or moreYou selected
FULL-DUPLEX-HF: Two HackRF peripherals with enclosures and telescopic antennas plus two Ham It Up RF upconverters for MF and HF bands.Estimated delivery:Add $15 USD to ship outside the US
Pledge $900 or moreYou selected
50 backers All gone!
PROTOTYPE: A HackRF prototype peripheral with laser-cut acrylic enclosure, telescopic antenna, extra antennas, a Ham It Up RF upconverter, and a HackRF PortaPack will ship in October. A final HackRF peripheral with enclosure, telescopic antenna and Ham It Up RF upconverter will ship in January.Estimated delivery:Add $30 USD to ship outside the US
- (35 days)