Share this project

Done

Share this project

Done
FLEKS3D makes 3D Printing EASIER, with a HIGHER SUCCESS RATE and SMOOTHER WORKFLOW
FLEKS3D makes 3D Printing EASIER, with a HIGHER SUCCESS RATE and SMOOTHER WORKFLOW
FLEKS3D makes 3D Printing EASIER, with a HIGHER SUCCESS RATE and SMOOTHER WORKFLOW
154 backers pledged $7,105 to help bring this project to life.

Use this space to cheer the creator along, and talk to your fellow backers.

Have a question?

Only backers can post comments. Log In
    1. Missing avatar

      Dale Watts
      Superbacker
      on

      Sorry $15. Its asking for more.

    2. Missing avatar

      Dale Watts
      Superbacker
      on

      Hi, I ordered the fleks3d 6x6 and 8x8 both simple build plates, but when I go in to my backerkit survey it says the price is more even though I backed it at $20.

    3. Timothy Stark
      Superbacker
      on

      Done. I submitted survey on backerit. I just ordered add-ons.

    4. Viktor Jondal & Peter Ragonetti 3-time creator on

      Hello Everyone,

      Following the campaign we will followup with a service called Backekit, which will allow you to add to your order.

    5. Missing avatar

      Glenn Wong on

      I pledged for the 9x6 system. I also want to pledge for the 12"x12" simple. Kickstarter will not allow two pledges. It can only allow you to change pledges. Please advise. Thanks.

    6. Missing avatar

      Midu on

      Hi there.
      I would like to know the thickness of the plate.
      Thanks.

    7. Xavier on

      @creator : I have exactly the same question as Adam Gilborne

    8. Rob States on

      This comment has been removed by Kickstarter.

    9. Missing avatar

      Adam Gilborne
      Superbacker
      on

      @creator
      I would like to plage for 2 FLEKS3D Simple 6"x6" .
      Can I pledge 30 usd or can I double the pledge in some other way?

    10. Missing avatar

      John Wilfong
      Superbacker
      on

      @Creator - Thank you for the clarification. I have a Zortrax M200 with a 8x8 build area. I do not want to mess with clips that the Simple requires. The System offer would reduce my build area to 7x7. I like the idea of a frame where the plate can be removed and switched or replaced quickly. I'm currently using a 10x10 buildtak plate system that works well but wanted to test your solution that doesn't use magnets. Thanks anyway.

    11. Viktor Jondal & Peter Ragonetti 3-time creator on

      Hello everyone, thank you for the enquires.
      John - frame is .5in thick. Takes out 1 in of printing area. For edge to edge print we recommend the "simple"
      Churchill - Theres typo on the 12x12in. Its 304.8x304.8mm (not 381x381). The CR-10 is 300 mm. So the plate will stick out 2,4mm on each side. Looking at images of the printer, it looks like there is room for that small amount of overhang.

    12. Churchill
      Superbacker
      on

      So the 12x12 is CR-10 size. I'll order one and see how it holds up.

    13. Missing avatar

      John Wilfong
      Superbacker
      on

      Is 8 x 8 the available print area and not size of frame? What's the dimension with frame on 'System'?

    14. Churchill
      Superbacker
      on

      381x381mm is too big. I'd have to trim the flexible bed down, is that even feasable?

    15. Shiki on

      CR-10 bed would be probably 12 x 12 inch version.

    16. Churchill
      Superbacker
      on

      Where is the CR-10 bed of 310x310? I'd buy 8 if i could get that size.

    17. Missing avatar

      Goh Jin Han
      Superbacker
      on

      Same here, CR-10 has been stored away as if it was in hibernation.

    18. Solice on

      Finally! I've been trying to order the 12x12 plates for quite some time!