Share this project

Done

Share this project

Done
Knife Edge Bit™ prevents slipping and stripping of screw heads! Use with existing tools. Saves time energy and money!
Knife Edge Bit™ prevents slipping and stripping of screw heads! Use with existing tools. Saves time energy and money!               Click below to go to our permanent site where you can order yours today!
Knife Edge Bit™ prevents slipping and stripping of screw heads! Use with existing tools. Saves time energy and money!               Click below to go to our permanent site where you can order yours today!
1,617 backers pledged $71,517 to help bring this project to life.

About this project

NEW Phillips Screwdriver that turns new AND damaged screws! project video thumbnail
Replay with sound
Play with
sound

NEW Phillips Screwdriver that turns new AND damaged screws!

$71,517

1,617

Hello, Thank you for viewing our revolutionary campaign. You'll be glad you did! 

Hello, First let us state that we have spent most of our lives working with tools. It is important to us that you understand that we do know what we are talking about. We had to experience the problems before we could seek the remedy. We are not wasting your valuable time. We would not do that. 

If you want a short third party version of our bit, here is a nice writeup on http://www.coolthings.com/knife-edge-pjillips-screwdriver-bit/ 
Something we would like to emphasize is that if you use our Knife Edge™ bit to begin with, you are very unlikely to ever see another stripped screw head from your work. It does make a nice removal tool but that is not it's primary function.

Thank you for reading on.

What if we told you that we have the one tool that you have always wanted? The one you thought you could never have because it didn't exist, before now? The instant you try it, you will want it, and once you have it, you will protect it, because losing it would make you far less effective, like you were before this. If you are like most of us, this is a tool that you think you already own several of, but you hate to use. This tool is (reluctantly) used at least as often as any other but often with problems and words you would not want your mother to hear that come directly from it's use. This tool was NOT designed to be used as it is today, but no one has ever explained to you why, until now. We looked around and tried everything we could find. What we found was that even though everyone we have ever talked to hates the way this tool works, No one had ever bothered to make the needed design improvements, so we did! Aside from the most basic shape that had to be maintained in order to still fit Phillips screws we made several major changes in almost every aspect of it's design so that it was satisfactorily updated to be efficient, effective and finally, gratifying to use. Odd's are you have old ones with you whether you are at home, work or driving. We are talking about Phillips screwdrivers. Specifically Phillips bits, the part that actually touches the screw to make it turn. Our advanced new "Knife Edge" bit for Phillips screws works with new screws or damaged old screws. Oily, rusty or dirty screws. Screws that before now had to be painstakingly removed and thrown away. Again, It works with most damaged, greasy, oily or wet screws the same way it does when you are in a clean, dry shop with new screws. It requires less effort than ever before and it works the same reliable way whether you use it for putting a project together or taking it apart. Sounds great doesn't it?

What you are about to discover can be life changing. (Your tool use may vary.) We promise not to waste your time. If you like what you see, Please support this project. Share this page with as many people as you can, every way you can. Again, sharing this page is the only way this will happen. Ask your friends to consider buying their own so they won't take yours. Spreading the word is what we need most. Your help is vital and only you can help make the difference!

Damaged Screws Easily Turned By Knife Edge Bit™ In Video Above.
Damaged Screws Easily Turned By Knife Edge Bit™ In Video Above.

Before we begin we would like to share with you the attributes we required of ourselves for our tool to be worthy of your support. 

1. You should instantly notice the superiority when you first use it without any doubt. 

2. It should save you time and/or money. Both would be best.

3. It should save you energy and help protect you from injury. 

4. You should want to think of it as your, ”only bit” after one use. You realize it's value and will not let the "Knife Edge" bit out of your sight once you have it. Old out of date bits will be retired. You'll have to experience it to fully understand.

As you will see we are proud to say that we have successfully accomplished all 4. 

Most of us learned at an early age the basics of tools, which hammers worked with nails, which saws cut wood or metal and certain screwdrivers worked with certain screws, right? Experience teaches us that if you apply your hammer properly you will drive a nail straight into your work every time as desired. Conversely, anyone who has ever tried to drive a Phillips screw knows the frustrating disappointment of using your best efforts trying to complete the simple task of turning a screw, only to watch that screw often become unusable as the bit pushes itself out and destructs the screw head right before your eyes. This out of date tool should be called the "Screw Destroyer", not screwdriver because it often destroys more than it drives. So now you’re stuck and it isn’t your fault! Here's proof.

Henry Phillips Patent For Driver To "Cam out" Or Push Out When It thinks It's Finished. It Served A Purpose Then. Now It's Part Of The Cause Of Your Problems.
Henry Phillips Patent For Driver To "Cam out" Or Push Out When It thinks It's Finished. It Served A Purpose Then. Now It's Part Of The Cause Of Your Problems.

Does this sound familiar? You have that little job on your list that you promised to take care of before you head out, only to be stopped in your tracks by a stripped screw head because the bit came out and destroyed it before you were finished? You are left with a screw that is not out and it’s not in. It’s just…there! You bite your tongue to not get in trouble but we all know the feeling, right? Now you either have to leave it for later or your plans have to change.

Wouldn't it be great if that simple task didn't have to turn into a frustrating all day job? It doesn't anymore. Please continue reading... 

To Understand The Solution You First Need To Understand The Problem. Henry Phillips introduced the "Phillips" bit for use on factory assembly lines back in the 1930's. General Motors was one of the first to use it for their late 30's Cadillac. In those days "Phillips" bits were driven by big high-powered factory machines that lacked the speed control that the tools we use today have. Because of this Henry’s Phillips bit was designed to deliberately "cam out" or push itself out of the screw at a certain point so that it wouldn't be so likely to destroy the screws or the cars in the factories. Those screws were made of much higher quality stronger steel than typically found today, so this was an important feature on an assembly line back then. Conversely that same old design is the precise reason it is so difficult to drive a screw today. You are using yesterday’s bits in a completely different situation with today’s modern drivers and they simply don't work like they should! It's true, that same old Phillips bit design that is still being sold today was never intended for use with the current tool technology we now use. So when you are fighting with your screwdriver bit trying to keep it in the screws please know that it is simply "caming out" just as it was engineered to do. The more you work at  it, the more you can bet it will come out and destroy your screw. 

While over the last 75 years other tools have progressed to be much better, Phillips bits themselves have changed little and unfortunately more often than not, softer screws have become commonplace. You probably never knew before that you are not to blame when that old bit comes out and consequently damages your screws, your work or sometimes, both.

In summary, now that you understand, if given a choice, you wouldn't expect to drive a nail straight with a rounded hammerhead; you would pick a hammer with a more appropriate flat striking surface, one with the handle at just the right angle to the face of the hammer so that when you strike the nail you can give yourself the best chance of success. Now you realize the need for a better Phillips bit for the same reason. Not one deliberately designed to “cam out” and strip your screws making unnecessary extra work for you but instead designed to make your work easier and much more reliable to complete the task at hand. We have done that.

Finally There Is A Better Bit! Great News!
Seriously, We have developed the first major technological improvement to the Phillips screwdriver in a very long time. Our new Patent Pending innovative "Knife Edge" bit has gone through extensive engineering and testing. It is designed for today’s tools and screws. We believe it is now the very best Phillips bit available. We know it sounds like we are saying we have the cure for some awful disease, but in this instance, we do!

The "Knife Edge" bit, Does not slip, Does not strip, Does not "cam" out, Does not destroy screws, Requires no extra force to stay in the screw, Drives dirty oily screws like dry screws, Drives most damaged screws and will often remove screws that before would not have been possible with a regular bit.

It grabs on to the screw like no other bit to offer you the most torque without damage. There are numerous unique patent pending improvements that all work together to make this the very best driver available today. It will drive damaged screws like new screws in both directions. Now you can drive Phillips screws without damaging your screw heads and without having to replace them! Think about the time that will save you and how much better your finished job will look.

What We Set Out To Do. 

From the very start our primary goal was that our "Knife Edge" bit had to work they way we have all wished for, it had to be compatible with the standard Phillips screws that fill the world of fasteners today or why bother? It also had to be compatible with current bit drivers and holders. Additionally since our founder has a bad shoulder we wanted a design that would no longer require the user to “lean” into or need to "muscle" the bit to try to make it work, which we were able to do. This had never been accomplished before. As a result of our other requirements we also created a bit that works in dirty oily screws the same as dry screws. Last but not least it had to drive a screw in either direction without damaging the head. These were major, we were not looking to make new screws to fit our new bit as others have done. In our view this would not be of much help since it is estimated that well over 80% of all screws in the world today are Phillips screws, we run into them daily, so creating the "Knife Edge" bit to work with those seemed obvious! We are pleased to report that the "Knife Edge" bit works extremely well, it works whether tightening or loosening, in areas with little or no leverage and on oily screws. When you start out with new screws, they can still look new after you have driven them by using the "Knife Edge" bit. And there is another added bonus...

Take It Easy On Yourself. Do More Work With Less Effort! 

How you ask? With the "Knife Edge" bits new design you place the bit in the screw as you normally do and squeeze the trigger on your driver. It will stay in the screw until it is all the way in or until you take it out. This is new and it is designed that way! No extreme force is required to keep it from slipping. No more leaning into the screw like before. No more sore shoulders. When you try it yourself you’ll be pleasantly surprised. Imagine how much easier your work will be without the unavoidable “workout” of the past? This is a tremendous advantage when you’re up on a ladder, reaching up over your head or out to the side or in any situation where you have reduced leverage or a lot of screws to drive. 

See The Curve In The Shadow Inside The Bit? It's Part Of What Makes It Work. It's Also The Inspiration For Our Logo!
See The Curve In The Shadow Inside The Bit? It's Part Of What Makes It Work. It's Also The Inspiration For Our Logo!



This is NOT one of those "disaster drill out and throw the screw away removal" tools that sell for about $20 and still leaves you missing a screw and with an unfinished job. By then, it’s too late!

While you will be amazed with how well the “Knife Edge” bit works with previously damaged screws that ordinary bits won't budge at all, it's important to know that when you use the "Knife Edge" bit to begin with it is very unlikely that you will ever have screws that need to be replaced. Have you ever had a screw strip out and you didn't have a spare that matched? Your project just went on hold until you can find a replacement screw. Now you can prevent that waste of time and money. 

Made For Todays Phillips Screws. It's Like Nothing Else You've Seen!
Made For Todays Phillips Screws. It's Like Nothing Else You've Seen!

The "Knife Edge" Bit Will Be Your Only Bit of Choice.
We have perfected the design of the "Knife Edge" bit, working prototypes have been made and they perform flawlessly. Trade Marks and Utility Patents have been filed with the U.S. Patent Office. The next stage is where we need your support to make the initial order of the "Knife Edge" bits to offer for sale. This is a serious professional grade tool. As such we will only make professional quality bits using the best materials and machining techniques available. This is important to understand because due to their very complex patent pending design these bits are much more expensive to make than the old style Phillips bits of the past. Those bits are generally made by stamping them out at speeds too fast to see. Our bit is much more multifaceted and the attention to detail is much higher with closer tolerances so those methods simply would not work for us. An example might be if you think about a table leg, one that is basically straight from end to end costs much less to make than one with lots of details that takes more time, labor and expertise so while our cost is more, they are worth every penny simply because the are so much easier to use, should last a lot longer and offer a much better result. In short, ours actually work!

The difference in cost is a small price to pay when compared to how much better the “Knife Edge” bit performs. Think of all the frustration you’ll no longer experience using this bit and they are less expensive than the rescue bits mentioned above. Also Henry's old bits do not last as long as preliminary tests have shown ours do because "KnifeEdge" bits don't bounce in and out of the screw heads beating themselves to death like before while they chew up your screws which is what greatly accelerates the wear and tear to Henry's old bits. 

Your support will mean that you will be among the very first to receive them. We are offering the most common sizes, a No.1 and a No.2 both as either a 1 ¼-inch length that fits a standard magnetic bit holder or as a 2-inch power bit that fits most power driven drills and chucks as well as others others. FYI Most screws take a No.2 bit. If they are smaller screws they will require a No.1 bit. Using the correct size, as with most things, is critically important.  If you are not sure we suggest you buy both and use the one that fits. This way your job will be easy to complete.

Please Follow Us On facebook. Go here and share with everyone. It will only take a minute and it makes a big difference!

A Final But Important Thought.
During the last two years we have worked with many people who without their skillful help we would have never made it this far. We appreciate them all tremendously and are forever thankful. We often heard from those who have worked with us in developing the "Knife Edge" bit that once you know about it, once you've tried it, every time you need to turn a Phillips screw, you will be glad you have one. Those that had our prototypes similarly said they were very relieved to have the right tool for the job. The instant you try it you will see why this could easily become the industry standard. Get yours now at this special offering and again, please share us with your friends so we can offer these to everyone as soon as possible! Thank you for your time and support! We seriously appreciate you! Please contact us with any questions.

Risks and challenges

We have worked on this full time for the last two years. Prototypes have been made necessitating engineering and design adjustments. More prototypes were made until it was exactly what we envisioned. Use it once, you will use it forever!

The only possible setbacks we can think of are if shipping takes longer than expected or unforeseen manufacturing difficulties arise, we have made allowances for both should they arise so we feel more than confident we will get this completed on time, if not sooner. We further commit that we will inform you if we should hear any different.

Learn about accountability on Kickstarter

Questions about this project? Check out the FAQ

Support this project

  1. Reward no longer available

    Pledge $10 or more About $10

    SUPER EARLY BIRD DEAL!
    THESE BITS WILL RETAIL FOR $14 DOLLARS AFTER THE KICKSTARTER ENDS.

    A very special Thank You! These will go fast! Limited to the first 500 supporters who tell everyone else about our Kickstarter and share this page. We greatly appreciate your spreading the word! You are on your honor, we know you want to help make these available to everyone so please do it now. Copy the link above in the address bar and share it now!

    Your choice of one (1) Professional Grade "Knife Edge" Bit for use with Phillips screws. Choose from a No.1 or a No.2, 1 1/4 inch bit. Fits any standard magnetic bit holder, Or (1) No.1or a No.2, 2 inch Power bit for use in power drill chuck and chuck adapters.

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 249 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  2. Select this reward

    Pledge $14 or more About $14

    YOUR NEW EVERYDAY BIT! You will not regret owning this magnificent tool!

    A very special Thank you. Limited to those who tell everyone else about our Kickstarter and share this page. We greatly appreciate your spreading the word! You are on your honor, we know you want to help! Copy the link above in the address bar and share it now!

    Your choice of one (1) Professional Grade "Knife Edge" Bit for use with Phillips screws. Choose from a No.1 or a No.2, 1 1/4 inch bit. Fits any standard magnetic bit holder, Or (1) No.1or a No.2, 2 inch Power bits for use in power drill chuck and chuck adapters.

    Less
    Estimated delivery
    Ships to Anywhere in the world
    277 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  3. Reward no longer available

    Pledge $27 or more About $27

    2 bits of your choice.

    "POPULAR DEMAND" Should have been the name of this bit!

    So many of you asked for this package that we had to include it for you.

    Same shipping cost as 1 bit!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 15 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  4. Reward no longer available

    Pledge $40 or more About $40

    BY POPULAR DEMAND All 4 bits (one of each- no mixing please) for our lowest price with the same low shipping cost as 1 bit. This saves you an additional $12.

    Total cost to you shipped is $44.
    Hurry as this won't last!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 250 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  5. Reward no longer available

    Pledge $44 or more About $44

    BY POPULAR DEMAND - AGAIN BECAUSE YOU ASKED!

    All 4 bits (one of each- no mixing please) for a great price with the same low shipping cost as 1 bit.

    This saves you an additional $8 off the bits plus lower shipping! Same as single bit!

    Hurry, this won't last! Sold out last time!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 71 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  6. Reward no longer available

    Pledge $44 or more About $44

    BY POPULAR DEMAND - AGAIN BECAUSE YOU ASKED!

    All 4 bits (one of each- no mixing please) for a great price with the same low shipping cost as 1 bit.

    This saves you an additional $8 off the bits plus lower shipping! Same as single bit!

    Hurry, this won't last! Sold out last time!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 200 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  7. Reward no longer available

    Pledge $48 or more About $48

    BY POPULAR DEMAND - AGAIN BECAUSE YOU ASKED!

    All 4 bits (one of each- no mixing please) for a great price with the same low shipping cost as 1 single bit!

    Hurry, this won't last! Sold out last time!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Reward no longer available 220 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  8. Select this reward

    Pledge $50 or more About $50

    FINAL DAYS - BECAUSE YOU ASKED!

    Any 4 bits, mix or match, you choose, for a great price, 6 dollars off! and still the same low shipping cost as 1 single bit!

    Hurry, only a short time left!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Limited 129 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  9. Select this reward

    Pledge $65 or more About $65

    ALSO BY POPULAR DEMAND - 6 bits of your choice mix or match with the same low shipping cost as 1 bit. This saves you an additional $20.

    Total cost to you shipped is $64.
    Hurry as this won't last!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Limited 131 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  10. Select this reward

    Pledge $100 or more About $100

    DISTRIBUTOR/PROFESSIONALS PACK 12 Professional Grade "Knife Edge" Bits for use with Phillips screws. $68 DOLLARS OFF RETAIL. Choose from No.1 or No.2 in either 1 1/4 or 2 inch power driver length. At this time we must ask that each order all be same size and length. Please share us with every one. Copy the link above in the address bar and share it now!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Limited 10 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.
  11. Select this reward

    Pledge $100 or more About $100

    CELEBRATION GOAL REACHED REWARD
    12 Professional Grade Knife Edge bits any size, mix or match, you choose! It costs more to sort for shipping but you deserve it! This is our way of saying Thank you for your support!

    Less
    Estimated delivery
    Ships to Anywhere in the world
    Limited 54 backers
    $
    Kickstarter is not a store.

    It's a way to bring creative projects to life.

    Learn more about accountability.

Funding period

- (30 days)