Solderdoodle Plus: Cordless USB Rechargeable Hot Multi Tool
Open Source touch control hot multi tool. Soldering iron, hot knife, needle, spade, scooper, and wood burning tips!
This project will only be funded if it reaches its goal by Tue, December 25 2018 5:19 AM UTC +00:00.
What is Solderdoodle Plus?
This campaign introduces a new Open Source USB rechargeable hot multi tool called Solderdoodle Plus, which is a cordless all-in-one soldering iron, 3D print finishing tool, and wood burning tool. Twice as powerful as the original Solderdoodle, it features 10 Watts of adjustable power with touch control and LED status indicators. Swipe to adjust power and press down to activate heat. Safety features include a sleep mode that disables the unit when not in use, low battery warning, and a dual-cell battery charge controller.
Solderdoodle Plus can last over 1 hour with constant maximum power at 500 Degrees C.
You can literally go anywhere and still have a way to charge your Solderdoodle Plus if there is a laptop, USB battery, wall adapter, or even a USB solar charger nearby!
Alternatively, you can use the Solderdoodle Plus as a corded device, which means it can charge and discharge at the same time.
Here's the link for the instructions on how to build the Solderdoodle Plus prototype"
Solderdoodle Plus uses a high-efficiency, high-power charge controller, uses similar batteries that are used in the Tesla electric car, and uses seven different replaceable tips.
Where Do the Funds Go and How Long Will it Take to Finish?
Solderdoodle Plus is here to meet your portable hot tool needs! In order to build the final production version at a reasonable cost, funds must be raised to purchase a minimum order of hundreds of batteries, cables, heating elements, circuits, and plastic components.
Solderdoodle Plus is designed be as simple to manufacture as possible and it is always being refined for the most efficient assembly. Our suppliers have given us great quality prototype parts and they are ready to manufacture the components in large quantities. Since this is a much more complex project than the previous Solderdoodle project, typical manufacturing lead-times for components will be about 60 days and test batches are always ordered before going in to large-scale production. Time is also required to refine the design from prototype to a final production ready product, which can take up to 60 days depending on possible bugs, added user interface features, or hardware improvements. Realistically, it should take about 12 months total to order parts, manufacture parts, inspect components, assemble each batch, final test each unit, package, and then ship them.
Retail Price for Solderdoodle Plus base unit is estimated to be $194 + shipping
Retail Price for a set of 7 tips is estimated to be $55 + shipping
Solderdoodle Plus Specs:
* Time to Fully Charge: ~3 hours
* Capacity: 2000mAh/7.2V * Type: 2X Panasonic NCR18500A Lithium-Ion
* Size: Diameter: 1.75 inches * Length: 8.5 inches
* Body Material: Nylon * Weight: 149g (5.3 oz)
* Input Cable - 3' Nylon Braided Male USB Type A to Micro Connector
* Input - Current: Up to 2500mA | Voltage: 5 Volts
* Output - Current: 2000mA | Voltage: 5 Volts
* Power Output: 10 Watts
* Battery Life Under Typical Use: 5-10 years until battery capacity significantly decreases
* Provides 1 hour of continuous heat at full power
* Heats up to over 572ºF (300ºC) in just 15 seconds
Solderdoodle Plus’ battery pack uses a charge controller on each cell. Each charge controller is on an isolated ground, ensuring each cell charges independently and never goes beyond the maximum and minimum voltage, which allows the cells to last 5 to 10 years before needing to be replaced.
Risks and challenges
I have a M.S. in Mechanical Engineering with over 10 years of experience and a few successful Kickstarter project under my belt. I also gained a lot manufacturing experience working at my Dad's sheet metal shop since I was a kid. Unforeseen issues that can delay the shipment of rewards to Kickstarter backers include, but are not limited to:
* Delays in receiving components on time from vendors.
* Delays from rejected parts during inspection.
* Delays from the carrier in shipping the product to the Kickstarter backer.
As a backer of other projects, I understand the importance of honest communication, even if the news is not so good, so I will make it a priority to answer all backer questions as fast as I can and give updates as soon as possible. We are on this journey together.Learn about accountability on Kickstarter