Use this space to cheer the creator along, and talk to your fellow backers.
Have a question?
Same here, didn't receive my card at all...
Have you all received your replacement cards? or I'm the only one to be robbed
by Pacunatt? I filed a complaint in my country, the cards have never been found (I wonder if it's really sent). Panucatt you owe me the sum of 150 € for the 3 cards ever received. Believe me, I will give you a very bad publicity.
Want an update too!!!
Any update on shipping the returned cards ?
Where did you find that version.
Can you please post the link.
I'm still waiting for my package, too. It was sent back as the customs did contact me too late about them having my package and when I went there after their message they already sent it back. This was in January. Still didn't receive my new package. When are you going to re-send it, Roy? You said before, that we will be contacted when it'll be resent, but that was in the beginning of May and still no message... :(
The rearm is now supported by marlin firmware. If smoothieware is not your cup of tea, then this is for you...and me ;).
And it is dead again. Configured everything via USB, everything went fine, display working, temps good, ethernet up and running, switched to 12V, and that was it. Display lit up for a second, died directly after that.
First and last kickstarter project for me, and first and last panucatt product.
Today I got my replacement board, and discovered what probably caused the first board to go up in smoke. It turns out the supplied cable for the rrd display is keyed wrong.
@adrian: we can wait for nothing. A shipment is provided under the same conditions as the first one. If you did not receive the first time, there is no reason to receive the second time for the same sending conditions. It becomes ridiculous. I really regret having to finance this project. I pay 3 cards for nothing. And the most ridiculous is to send them back under the same conditions. We will never get our purchase. This is one of my worst experiences on kickstarter
And... Still waiting. :-(
Npn I hate autocorrect.
Once I finally got around to figuring it out, it appears to work like a treat. I must add it does not play nice with proximity sensors. I had to build an inline jumper with an non transistor and resistor to get a signal on it. Works a treat now. Drives 4 0.9* stepper motors at 1/32 micro stepping, E3D Titan and v6, silicone bed using an mks 2.8" tft controller. Easier to configure when I need to make changes but I miss my marlin in a way. Bed height is kinda an issue which I will hopefully resolve when I get around to designing a bracket to hold the bltouch. Nothing I can't compensate for in software in the mean time.
So you intend to return the cards under the same conditions as your first shipments? If people have not had it the first time, why do you think they will have the second time with an identical shipment? Has my packet gone home or it's stolen ?
Hi Guys, I apologize for the late reply. We received notice of a bunch of returned packages. We will be sorting through them as some has torn or unreadable labels. They will be reshipped and you will be informed.
If you need support with your unit please open a ticket at support.panucatt.com
@flexfloo - Once the shipment leaves we have no control over it. I understand your frustration but the tracking only updates while in the USA and stops as it leaves and will not update until the local post office. I will see what else I can do.
Still waiting for mine. Roy's speed at replying to messages is worse than snail mail, if he does at all ! Tried his website but also nothing. Is anyone who has their card, finding it worth it ?
3 months day to day, still nothing in my box to the letter, the famous tracking of the parcel indicates expired. You need my money for cards. I have never received my cards ,so return my money. You do not reply to any message. I will not do the job of tracking my package for you. I am sorry to have participated in your campaign. For the moment I consider you a thief (I do not have a product and you reply to no message). I report your campaign to kickstarter and you can count on me to make you bad publicity. I encourage all unsatisfied backers to appeal against you and your company. You do not respect your backers. An unsatisfied backer.
Just wondering if anyone has tried/got the 12864mini oled display from makerbase on aliexpress to work? It works on ramps/Marlin with som pin tweaks
I have the same problem as you. I am waiting for my 3 re-arm cards. My package was sent for a reception without signature. Everyone can pick up my package. This is very serious, especially for sending 3 cards. I'm sure my package is lost or stolen. I'm very disappointed by Panucatt device and roy. you sleep ? A lot of backers don't have their package.
Wake up ? Do you act at least? $ 150 for nothing, the business is very juicy.
My RE-ARM board still haven't been delivered after 3 months, tracking number: LJ926980707US.
PLEASE VERIFY THIS WITH USPS AND SEND ME FEEDBACK!
I can confirm that MKS TFT32 works with RE-ARM through UART0
I've figured out how to get the board into dfu/bootloader mode to manually flash the firmware if anyone needs to try that route.
Have you tried to autotune pid? Check out smoothie http://smoothieware.org/temperaturecontrol or http://smoothieware.org/3d-printer-guide. Have you also upgraded to the latest firmware? I can't really test anything right now because my board doesn't read my sdcard or any for that matter and waiting for a response back from Roy. Is anyone else having the same problems? Anyone having a no response to anything and the board won't upgrade the firmware?
Anyone have problems with hotend pid tuning? I have very much problems to get hotend pid ok. Normally temp leave very much under what that need to be. And if you are near to setpoint takes minutes to get right temp set.
Thinking are that possible ramps have bad Mosfet with 3.3v gate voltage?
Or is that something else what i can do?
Hello, it will soon 2 months since my package was sent. To this day, I still have not received anything. How long should I wait? Maybe 3 months. I think my package is totally lost so I can not use the 3 cards I buy. I simply ask for the refund of the 3 purchased cards that I have never received.
Mine seems to have been sent back for none payment of custom fees. I didn't get any notification of this. Looks like I got a long wait for my re-arm lol. Roy has replied, but has taken him a while.
Have any chinese friends get the reward? I'm backer 372, shipped Jan 7th. After 2 month it's still on the sea?
Received mine in the uk a couple of weeks ago, any news on the K40 shield?
Hello friends french, have you received your reward well? Personally I still have not received anything and I'm starting to be worried
received mine today ! black and gold is REALLY sexy
About the z axis induction sensor. Had the same problem but worked when I configured it with a pull down resistor I mean
also you need to define that there is no min endstop for z
Roy sent me tracking number. Thanks for the prompt answer !
Hey backer 508 here. Still no tracking number (international) and no package either. What is happening ?
RRD cables didn't work for me. Screen would flash each time I turned the dial or press. Pulled my hair until I decided to try to make from the old cable, splicing the +5 straight to the PSU. Works! Just debugging my config file (the press to select button is killing the board, and the steppers need adjusting so they move instead of buzz). Thanks!
Not sure if anyone else has/had the same issue. My tracking shows my board is stuck somewhere between LA and the UK, Since 21st Jan... No reply from Roy yet.
Hello, friends French users? Has anyone ever received his reward?
I have had difficulties with a ramps, rrgraphical display (that works fine on a mega) on the re-arm with the cartisian config (with the display settings from the delta) not displaying, but the delta config does display, any suggestions?
Some reason not can edit old message :( Can i use Vin barrel jack to supply 12volts to board and still use usb to communication to computer?
Or do i need use USB (jumper) if i use this with computer. Love to use this with computer but maybe here is some problems that usb not can carry much power what re-arm board needs. Board start working normally when take ramps out off that. Now that works again when i put ramps back to re-arm. I still think there is some problems to board not get enough "juice" on usb jack.
Not get any connection with Windows 7 computer too. Only shows device manager "unknown devices" spot "Smoothie". Not see com port or sd card on windows "my computer" view.
Linux tells this kind of message on dmesg console command
"[ 1081.954950] usb 1-1.4: new full-speed USB device number 8 using dwc_otg
[ 1082.070684] usb 1-1.4: New USB device found, idVendor=1d50, idProduct=6015
[ 1082.070725] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1082.070745] usb 1-1.4: Product: Smoothie
[ 1082.070763] usb 1-1.4: Manufacturer: SmoothieWare
But not get any connection on octoprint to re-arm board. Before this problem there is always one option on Serial port -menu. Now there is only AUTO and that not find anything.
Hope someone have same problems and some solution to that.
Other problem is whole board is couple times now "dead". Last time i get that working to format sd card and put image again there and restart again and shutdown and put config file back to there. Just doing something like that that started working again normally.
Now board do same problems. When i start board nothing comes to lcd, octoprint not see any devices on USB port. Now try to sd format etc many times nothing helps. Is this board that kind easy to broke down totally? Or do some one have any tips how that goes back to working condition.
Are there any restrictions to the SD cards?
I can't get my SD Card working. I have a Kingston 8GB microDS HC class4.
I don't see the Card on my PC connected to USB. And it seems that the config.txt isn't loaded.
Because the Network module and the Display aren't operating, too.
Now i started to change my old printer to Re-arm everything else is going quite ok. M80 command give me some kill switch message, but that not so big problem.
Biggest problem is i dont get my Inductive sensor working smoothie at all. My mechanical endstops work ok on x and y axles. But z axle induction probe not working. I attach that on 1.28 or 1.29 and try to use z azle min ja max slots on ramps. But i dont get any changes z endstop state on M119 gcode. My induction sensor works realy well on marlin firmware. I measured that induction sensor give 3.3volts positive on mainboard when not triggered and 0.2volts when triggered.
But i dont get any changes to firmware state.
I got mine today, 7€ customs due (nice that you did not send with UPS or DHL Express, they add a 10€ charge on top). I need some tome to install it on my Trium3D (another kickstarter) Thanks!
Got someone a config for me for a core xy?
I tryed many things but the axis moves where ever they want and my Bed Temperature ist
constant on -25°C ... I'am not living in a Freezer. :D
Thanks Roy, board is arrived today. Not have time to start installing that now. But want to ask Roy @Roy Cortes or @all are they some tested or best microsd cards to that use. microsd card is needed to change and do settings on firmware on smoothieware if i am right?
I dont use microsd anything else only that firmware settings. I use octoprint to do all printings.
Thanks that was very helpful
1st basic tests worked fine.
RRD Full Graphic Smart LCD: o.k
see more on https://blog.georgmill.de/2017/02/07/32-bit-3d-printerboard-re-arm/
It runs only Smoothieware ?