The Heatworks MODEL 1 is now certified by TUV to UL 499 standard. Our certification information can be found under the Certificationtab of the SIZING & SPECS page of... Read more
To all backers,
Thank you for your patience and support throughout our campaign. You have been great! As we approach the last weeks of shipping backer orders, we want to... Read more
As we continue shipping MODEL 1s, we want to remind everyone that it is best to contact us directly, either via email or private message, should you... Read more
We are just as frustrated as you with the past delays in production and shipping. However, we are now producing and shipping MODEL 1 units, which was our... Read more
Weekly Production Update
Production continues to go well, and we have increased our rate of shipping from last week! We are confident that we will fulfill at least the first... Read more
Weekly Production Update
Things have continued to go well with production. We are producing and shipping units at an increased rate from last week, and continue shipping backer orders as quickly as units... Read more
Weekly Production Update
Production is in full swing at Flextronics and is continuing to go well. Although we are not yet producing at full production capacity, we should reach that goal in the... Read more
Production at Flextronics
This week production continued at Flextronics and is going well. The number of units shipping should increase next week as we build our inventory and work toward our production goals,... Read more
PRODUCTION AT FLEXTRONICS HAS STARTED!
We are really excited to announce that we have resolved the sealant issue and that production has begun at Flextronics! Jerry, Mike, Eric and the rest of the team have... Read more
Test Racks at Flextronics
Our brand new test racks just approved at Flextronics in Raleigh NC, on their way to Flextronics' Columbia plant for installation and the commencement of operations on Monday!
During the process of assembling units in our lab, we have found that one of the sealing materials that we have been using has recently exhibited inconsistencies in curing, which... Read more
Heatworks at the Consumer Electronics Show in Las Vegas
Heatworks teamed up with Qualcomm to demonstrate a WiFi enabled MODEL 1 at the Consumer Electronics Show in Las Vegas last week. Below are pictures of our exhibition and demonstration.... Read more
Transition to Flextronics
Although we have experienced some delays with our transition to full production, Flextronics will begin production the first week of February. We will, however, continue producing and shipping units until... Read more
Happy holidays from ISI Technology! Although our production ramp has been slower than anticipated, we are steadily working toward our goal of producing and shipping 100 MODEL 1s... Read more
More good news! Our transition to full production is moving forward and we are working diligently to achieve our goal of over 100 units a day. We recently brought on... Read more
The day we have all been waiting for has arrived!
We started shipping the first batch of MODEL 1s yesterday, with a further ramp in production this week! It is our goal to get to 100 units a day in the... Read more
Hey, a schedule!!!!!
So we now have a delivery date for the circuit boards, which is the lastcomponent we were waiting for! The first 500 show up on 11/24, with assembly and... Read more
So we have the o-ring issues resolved, and even though the regular temperature triacs seem to be working fine, we have decided to go with the higher temperature... Read more
We have received the 5,000 o-rings and are testing them to be sure that they work, and the right color plastic resin should arrive at our vendor tomorrow,... Read more
Latest update....vendor issues :(((
I hate to tell you, but we have been delayed by two different vendor issues. The first is that the plastic molding house molded the housings in the... Read more
Not much is new from last week ( we start production next week) except that we are pleased to announce that every MODEL 1 will ship with a... Read more
It has been very challenging around here, but production is now scheduled to begin at our supplier in Columbia, South Carolina on August 11. The first batch of molded... Read more
The molding tools are at eNNOVEA, which is our new plastic parts molding house!
Here is one of the tools. They will start molding parts for us next week. Getting close!
Thanks for your support,
Big day for us, the molding tools have arrived in the USA!
Our supplier nightmare is almost over! The plastic part molding tools are in the US after air freighting them from China. They have not cleared US Customs yet, but they... Read more
I hope all of you are doing well. I can say today that we are doing better than we have been. We have spent the last five weeks dealing with an... Read more
We are going to present at TechCrunch Disrupt NY 2014 Battlefield tomorrow!
We have been selected to present ISI Technology’s Heatworks MODEL 1 in the Battlefield at this very cool event! You can learn more about it at http://techcrunch.com/events/disrupt-ny-2014/event-home/ Our presentation will... Read more
Today is Earth Day
We should continue to support initiates that preserve and protect Mother Earth. All of you are one step closer, by saving water and energy with the MODEL 1.
Thank you... Read more
Here is the latest update. Generally things are going well, except for three plastic parts which needed some dimensional tweaking. The molding tools are in China and the... Read more
First batch of parts are here!
We just received the first batch of production plastic parts in our lab! The color will be a bit brighter white, but dimensionally, they look very good. The tube... Read more
Here's the latest MODEL 1 update!
Here is what is happening around here. Our plan is to build fifty units from production tooling, test them in our lab, and get some units out to the... Read more
We have been getting some terrific media coverage! Check this out and thanks again for your support!
The installation video is up at www.myheatworks.com
For our metric friends, you can use a 22mm "push-fit" coupling (such as sold by John Guest) to connect the inlet and outlet water pipes in place of the 3/4"... Read more
Hello everyone and thanks again for your support and interactions.
This has been a great campaign, and we cannot wait to get the product out to you.
The installation video... Read more
Wow, what a week! We continue to enjoy great interactions with you, which goes to the heart of our campaign. I have been surprise at how many of you want... Read more
Dear Heatworks Supporter,
It’s getting hot here! We’ve hit our Kickstarter goal for Heatworks, thanks to all of your support. In just over a week, we’ve raised more than $140,000.... Read more
Another great morning! Over 100% funded!
Hey everyone, thanks so much for getting us funded! What I have enjoyed the most is the interaction I have had with so many of you. I have also been... Read more
What a great morning!
I woke up to see that we are over 75% funded! Thanks to all of you for your support. It has been really invigorating to see how the community has... Read more
Answers to FAQs
Hey everyone, I have been getting a lot of messages and feedback (over 100 so far!), so I thought I would add the following information. As always, please contact us... Read more
Hey everyone, I wanted to say thanks to all of you who have backed us so far. We just reached our halfway goal, and to do it in only three... Read more